The short version of secretagogue fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-08-01. Anything still debated is marked as such rather than presented as settled.
Reversed-phase high-performance liquid chromatography is the standard method for purity assessment, most often on a C18 column with a water and acetonitrile gradient and trifluoroacetic acid or formic acid as an ion-pairing agent. Mass spectrometry by electrospray or matrix-assisted laser desorption confirms the expected mass and reveals truncated or modified sequences. Amino acid analysis and sequencing provide orthogonal structural evidence. Typical impurities include deletion sequences, oxidized products, and dimeric species. Detection wavelength, usually 214 or 220 nanometers, should be reported because response factors differ between peptides.
Purity is normally reported as a percentage of total peak area, a figure that does not account for water content, residual solvents, or counterions. Trifluoroacetate and acetate are the most frequent counterions in lyophilized peptides, and they shift the true peptide content away from the mass of the powder. A separate quantitative assay is therefore needed to state content accurately. Certificates of analysis often omit these details, which makes batch-to-batch comparison difficult and limits conclusions drawn when results from different suppliers are compared.
Lyophilized material is generally held at minus twenty degrees Celsius or lower, protected from moisture and light. Repeated excursions to room temperature cause condensation inside the vial and gradual moisture uptake, both of which shorten shelf life. Containers should be allowed to equilibrate before opening so that water does not condense on the solid. Dividing a batch into single-use aliquots reduces freeze-thaw cycling. Solid peptide handled this way is usually considered stable for months to years, while the same material in solution degrades on a much shorter timescale.
Ipamorelin is a synthetic pentapeptide first described in the 1990s by researchers at Novo Nordisk during a program to develop selective growth hormone secretagogues. Its sequence is Aib-His-D-2-Nal-D-Phe-Lys-NH2, incorporating two non-natural residues, alpha-aminoisobutyric acid and D-2-naphthylalanine. The C-terminus is amidated, and the material is supplied as a white lyophilized powder. The molecular formula is C38H49N9O5 and the monoisotopic mass is approximately 711.85 daltons. The short chain and modified residues give it greater resistance to enzymatic degradation than many larger peptide hormones.
At the molecular level, ipamorelin acts as an agonist at the growth hormone secretagogue receptor type 1a, the same G protein-coupled receptor that binds ghrelin. Receptor activation couples to Gq/11 signaling, raising intracellular calcium through inositol trisphosphate and diacylglycerol, which in turn promotes exocytosis of growth hormone from pituitary somatotroph cells. Ipamorelin binds this receptor with high affinity and shows weak activity at other secretagogue-related targets in vitro. Its action requires the intact receptor and is not reversed by growth hormone-releasing hormone antagonists.
| Property | Value | Notes |
|---|---|---|
| Purity method | Reversed-phase HPLC | C18 column, UV detection at 214 nm |
| Identity method | Mass spectrometry | Electrospray or MALDI-TOF |
| Solubility | Soluble in water and DMSO | Dissolution may require brief mixing |
| Storage temperature | -20 °C or lower | Desiccated and protected from light |
| Counterion form | Trifluoroacetate or acetate | Affects measured peptide content |
Storage recommendations for the dry solid center on low temperature and low moisture, most often -20 °C in a sealed, desiccated container protected from light. Solutions are less stable than the powder and are usually kept cold and used within a short window. Freeze-thaw cycling is a recognized source of loss, and aliquoting before freezing is a standard precaution. These practices derive from general peptide handling principles rather than from a single published stability trial, so exact shelf lives should be treated as approximate.
Analytical confirmation relies on reversed-phase high-performance liquid chromatography, often coupled to mass spectrometry for identity and purity assessment. Mass spectrometry distinguishes the intact molecule from truncation products and from oxidation or deamidation variants that share similar chromatographic retention. Immunoassays appear in some biological studies but can cross-react with related peptides, so they are weaker tools for identity work. Reported purity figures depend heavily on the gradient, detector, and integration method used, which complicates direct comparison between laboratories.
Published discussion of this compound is uneven. Some references describe it as a tool for probing growth hormone regulation, while others focus on analytical characterization or on comparisons with related secretagogues. Statements about selectivity, half-life and potency often trace back to a small number of original reports that later authors cite secondhand. Readers evaluating a claim should therefore check whether a figure reflects a direct measurement or a repeated citation, and whether the underlying study was conducted in animals, in isolated cells or in human volunteers.
Identity and purity assessment for a research peptide of this kind typically combines reversed-phase high-performance liquid chromatography with mass spectrometry. The chromatographic run separates related impurities and yields a purity percentage, while electrospray ionization or matrix-assisted laser desorption mass spectrometry confirms the expected molecular mass. Amino acid analysis or tandem mass spectrometry sequencing can add confidence when material is intended for quantitative work. Laboratories differ in how they calculate and report purity, so figures from different sources are not always directly comparable.
Lyophilized material is generally stored cold and dry, with desiccant, and protected from light. In solution the peptide is more vulnerable: the histidine side chain can oxidize, and repeated freeze-thaw cycles promote aggregation and loss of material to container surfaces. A mildly acidic aqueous buffer is often used for short-term handling because it limits several degradation routes. Accurate prediction of long-term stability under a given set of conditions is difficult, and published stability data remain sparse.
Selectivity is the property most often attached to this peptide. Published animal and early human studies record increases in growth hormone release after administration, with adrenocorticotropic hormone and cortisol responses remaining small by comparison. Effects on appetite-related pathways also appear weaker than those reported for several earlier secretagogues. Reviews that compare members of the growth hormone secretagogue family cite these findings frequently, though the receptor-level explanation for the selectivity continues to be debated rather than settled.
Ipamorelin is a synthetic pentapeptide classified as a growth hormone secretagogue. Its sequence, Aib-His-D-2-Nal-D-Phe-Lys-NH2, combines three non-proteinogenic residues with a C-terminal amide. The N-terminal aminoisobutyric acid unit and the two aromatic D-amino acids distinguish it from peptides assembled only from standard L-amino acids. Its formula is C38H49N9O5, corresponding to an average mass near 711.9 Da. At neutral pH the molecule carries a net positive charge, a property that shapes its behaviour in chromatographic and electrophoretic systems.
GeneReviews/NCBI/NIH/UW entry on APC-Associated Polyposis Conditions OMIM entries on APC-Associated Polyposis Conditions[link removed] Adenomatous+Polyposis+Coli+Protein at the U.S. National Library of Medicine Medical Subject Headings (MeSH) GeneCard Database concerning peer-reviewed reports on cancer critical alteration in several genes including (APC (protein)), (TP53), (Beta-catenin|β-catenin) Human APC genome location and APC gene details page in the UCSC Genome Browser.
TMEM125 has two variant transcripts that differ only in the 5' untranslated region (UTR), but both encode the same protein. mRNA variant 1 represents the longer of the two variants and is 1898 base pairs (bp) in length; variant 2 is 1797 bp long. TMEM125 microarray-assessed expression patterns in normal human tissue demonstrate the primary tissues of expression are the pancreas, lungs, salivary glands, trachea, brain, prostate, spinal cord, and thyroid. Additionally, RNA-seq data illustrates transcript expression in the following additional tissue: colon, small intestines, prostate, and stomach. TMEM125 comprises 219 amino acids with four transmembrane domains. Its predicted isoelectric point is 8.32 and predicted molecular weight is 22.1 kDa. It is primarily leucine-rich, and secondarily alanine- and glycine-rich; TMEM125 is also arginine- and lysine-deficient. It has two core repeat blocks, VALL and TTSS, which both appear twice within the protein. The secondary structure of TMEM125 is predicted to consist of α-helices and small segments of β-sheets.
In both pharmacology and nutrition sciences, bioavailability is measured by calculating the area under curve (AUC) of the drug concentration time profile. Bioavailability is a term used to describe the percentage of an administered dose of a xenobiotic that reaches the systemic circulation unchanged. It is denoted by the letter f (or, if expressed in percent, by F). In nutritional science, which covers the intake of nutrients and non-drug dietary ingredients, the concept of bioavailability lacks the well-defined standards associated with the pharmaceutical industry. The pharmacological definition cannot apply to these substances because utilization and absorption is a function of the nutritional status and physiological state of the subject, resulting in even greater differences from individual to individual (inter-individual variation). Therefore, bioavailability for dietary supplements can be defined as the proportion of the administered substance capable of being absorbed and available for use or storage.
Sources: en.wikipedia.org
Caffeine consumption during pregnancy is associated with increased risk of pregnancy loss and increased risk of low birth weight, defined as below 2500 grams (5.5 pounds). The European Food Safety Authority and the American Congress of Obstetricians and Gynecologists concur that habitual caffeine consumption up to 200 mg per day by pregnant women does not give rise to safety concerns for the fetus. The United Kingdom Food Standards Agency had recommended that pregnant women should limit their caffeine intake to less than 300 mg of caffeine a day, but in 2009 revised that downward to less than 200 mg of caffeine a day. High doses of caffeine intake during pregnancy may increase the risk of miscarriage and some major negative pregnancy outcomes, such as stillbirth or low birth weight. A 2020 review called into question the safe levels proposed by the European Food Safety Authority, the American Congress of Obstetricians and Gynecologists, the National Health Service, and the Dietary Guidelines for Americans. It found that the current scientific evidence does not support moderate caffeine consumption during pregnancy as safe, and advised pregnant women and women contemplating pregnancy to avoid caffeine.
Altria, like other tobacco companies, has invested in science and medical companies which develop and produce medical products for conditions caused or aggravated by smoking. As of 2024, Altria's three medical subsidiaries included the following: Cronos group (maker of recreational cannabis), Lexaria Bioscience (Developer of proprietary drug delivery technology, DehydraTECH, to improve active pharmaceutical ingredients entrance into the bloodstream) and Micreos (biotech company focused on discovering and developing recombinant proteins for chronic dermatology and oncology conditions). It has also designed and marketed electronic cigarettes. Altria launched the MarkTen and Green Smoke brands. Both of these were discontinued in December 2018. The company returned to this market through the acquisition of NJOY.
The linear amino acid sequence of a protein is called the primary structure. The primary structure can be easily determined from the sequence of codons on the DNA gene that codes for it. In most proteins, the primary structure uniquely determines the 3-dimensional structure of a protein in its native environment. An exception is the misfolded prion protein involved in bovine spongiform encephalopathy. This structure is linked to the function of the protein. Additional structural information includes the secondary, tertiary and quaternary structure. A viable general solution to the prediction of the function of a protein remains an open problem. Most efforts have so far been directed towards heuristics that work most of the time.
The catalytic mechanism of FGE is well studied. A multistep redox reaction with a covalent enzyme: substrate intermediate is proposed. The role of the cysteine residue for the occurring conversion was studied by mutating the cysteine to alanine. No conversion was found using mass spectrometry when the mutated peptide tag was used. The mechanism shows the important role of the redox active thiol group of cysteine in the formation of f(Gly), as seen in Fig. 2. The key step of the catalytic cycle is the monooxidation of the cysteine residue of the enzyme, forming a reactive sulfenic acid intermediate. Subsequently, the hydroxyl group is transferred to the cysteine of the substrate and after hetero-analogous β-elimination of H2O, a thioaldehyde is formed. This compound is very reactive and easily hydrolyzed, releasing the aldehyde and a molecule of H2S,
Sources: en.wikipedia.org
Ethane-1,2-dithiol, also known as EDT, is a colorless liquid with the formula C2H4(SH)2. It has a very characteristic odor which is compared by many people to rotten cabbage. It is a common building block in organic synthesis and an excellent ligand for metal ions. Ethane-1,2-dithiol is made commercially by the reaction of 1,2-dichloroethane with aqueous sodium bisulfide. In the laboratory, it can also be prepared by the action of 1,2-dibromoethane on thiourea followed by hydrolysis. 1,2-Ethanedithiol is a weak acid, typical of alkyl thiols. In the presence of base and an alkylating agent, 1,2-ethanedithiol converts to thioethers: HS(CH2)2SH + 2 NR3 + 2 R'I → R'S(CH2)2SR' + 2 [R3NH]I Oxidation of 1,2-ethanedithiol gives a series of oligomers, including the cyclic bis(disulfide). As a 1,2-dithiol, this compound reacts with aldehydes and ketones to give 1,3-dithiolanes, which can be useful intermediates.
Automated synthesis systems are laboratory robots that combine of software and hardware. As synthesis is a linear combination of steps, the individual steps can be modularized into hardware that accomplishes the specific step (mixing, heating or cooling, product analysis, etc.). Such hardware includes robotic arms that use dispensers and grippers to transfer materials and shakers that adjust the stirring speed and cartesian coordinate system robots that operate on a X Y Z axis and can move items and perform synthesis within designated bounds. Conditions of reactions (atmosphere, temperature, pressure) are controlled with the help of peripherals like: gas cylinders, vacuum pump, reflux system and cryostat. Modular platforms use a variety of tools in order to perform all the unit operations needed in synthesis. There are many commercial modular hardware solutions available to execute synthesis. New software programs are available that can compile an automated synthesis procedure in executable code directly from existing literature. There are also software programs that can retro-synthetically generate a procedure at the level of proficiency of a graduate student.
These cyclic dipeptides incorporate both donor and acceptor groups for hydrogen bonding. They are conformationally constrained nearly planar scaffolds. Diversity can be introduced at up to six positions and stereochemistry controlled at up to four positions. They are stable to proteolysis. These characteristics underpin theis biologically activity and utility in medicinal chemistry. As a consequence of their predominant biosynthetic origin from L-α-amino acids most naturally occurring 2,5-DKPs are cis configured as the cyclo(L-Xaa-L-Yaa) isomers. 2,5-DKPs epimerize under basic, acidic and thermal conditions. The composition of the cis and trans isomers in the equilibrium state varies widely depending on the bulk of the side chains, if a ring (e.g. proline) is present, or if the nitrogen atoms are alkylated . Although epimerization was historically an issue in the synthesis of 2,5-DKPs, several mild methods have been developed recently that avoid epimerization.
Prolactin is available commercially for use in other animals, but not in humans. It is used to stimulate lactation in animals. The biological half-life of prolactin in humans is around 15–20 minutes. The D2 receptor is involved in the regulation of prolactin secretion, and agonists of the receptor such as bromocriptine and cabergoline decrease prolactin levels while antagonists of the receptor such as domperidone, metoclopramide, haloperidol, risperidone, and sulpiride increase prolactin levels. D2 receptor antagonists like domperidone, metoclopramide, and sulpiride are used as galactogogues to increase prolactin secretion in the pituitary gland and induce lactation in humans. Breast-feeding Breastfeeding and fertility Epileptic seizure Hyperprolactinaemia Hypothalamic–pituitary–prolactin axis Male lactation Prolactin modulator Prolactin receptor Prolactin-releasing hormone Prolactinoma Weaning MedlinePlus Encyclopedia: Prolactin Overview of all the structural information available in the PDB for UniProt: P01236 (Prolactin) at the PDBe-KB.
Stomach upset Intestinal gas Nausea Liver damage (similar to other niacin products) It is marketed as "no-flush" niacin, but research suggests that the lack of flushing may be due to its limited conversion to active niacin. Inositol nicotinate should be used with caution in individuals with certain conditions: Diabetes: May raise blood sugar levels. Diabetic patients should monitor their blood sugar levels closely. Liver disease or kidney disease: Niacin can accumulate in people with liver or kidney problems, potentially worsening their condition. Bleeding disorders: Inositol nicotinate may slow blood clotting, increasing the risk of bleeding for individuals with clotting disorders or those undergoing surgery. Gout: Large amounts of niacin may trigger gout attacks.
Sources: en.wikipedia.org
It is reported as the percentage of total peak area in a reversed-phase chromatogram. That number does not reflect water content, residual solvents, or counterions. The actual peptide content is therefore lower than the stated purity figure suggests.
Trifluoroacetate and acetate are common in lyophilized peptide preparations. They contribute to the mass of the powder without contributing to the peptide itself. This shifts the true content and can affect results in biological assays.
Hydrolysis and oxidation are the primary pathways. Alkaline conditions accelerate hydrolytic cleavage of the chain. Oxidation most often involves susceptible residues, producing products that appear as earlier or later peaks in chromatographic analysis.
It is a synthetic pentapeptide belonging to the growth hormone secretagogue family. Its principal characterized target is the ghrelin receptor, also called GHS-R1a. The molecule contains non-natural amino acids and an amidated C-terminus.